What does FH mean on Maytag washer

FH indicates that there is a Water Inlet Problem—no or insufficient water supply. Select PAUSE/CANCEL twice to cancel the cycle. Unplug washer or disconnect power.

How do I fix the FH code on my Maytag washer?

Turn off the water and remove inlet hoses from the inlet valves in the back of the washer. Inside the inlet valves are screens. Remove any accumulated film or particles from the screens. Reinstall hoses, turn on water, and check for leaks.

What does it mean when a washer says HF?

The H/F error code indicates that the control did not sense any water filling into the unit. Be sure that the drain hose is not down into the drain pipe too far; this will create a siphon & the H/F error code.

How do I reset my Maytag washer?

1. Press the “Power/Cancel” button. …
2. Push the appropriate button to choose a new cycle.
3. Press “Start/Pause.” You have now reset your Maytag washer.

What does F 09 mean on a washing machine?

Whirlpool Duet Washer Error Code E01 F09 means LONG DRAIN TIME. When your Whirlpool washer goes into drain mode and the drain time is past 8 minutes and not reaching the reset level in the pressure sensor then the valves in the drain are turned off and the drain pump will cease to pump out the water.

How do I fix error code F20?

To reset the f20 error code, exclude the program crash of the Whirlpool washer. To do this, de-energize your washing machine for 10-20 minutes, then turn it on back. If the error disappears from the display, the problem is successfully eliminated.

What does F 20 mean on a Maytag washer?

F20 Error Code F20 indicates a water inlet problem—no water or insufficient water supply. Try the following method to resolve: Select PAUSE/CANCEL twice to cancel the cycle. Unplug washer or disconnect power.

What are the codes for a Maytag washer?

Error CodeErrorSud or SdThere are too many suds in the washing machine.F5 E2The door is not locking properly.F7 E1Indicates a motor speed sensing error,F8 E1 or LO FLThe washer is sensing a low flow of water.

Does Maytag washers have a reset button?

Press and hold the Start/Pause button for 3 seconds. All indicator lights should be off at this point. Reset the Washer: To reset (clear) the washer, rotate the Cycle Selector Knob counter-clockwise (left) to clear any sequence.

What does F5 mean on my Maytag washer?

Did you receive a F5 E2 lid lock alert? The F5 E2 alert indicates the washer can’t engage the lid lock because there may be an obstruction in the lid lock area. Please check the lid lock area and remove any objects in that area.

Article first time published on

What does FH mean on Kenmore washer?

The FH error code indicates that the washer control does not detect water entering the machine within 30 seconds after the fill valves have been opened. It is also displayed after 8 minutes if the flow sensor has detected 10.5 gallons passing through it without the water level pressure switch tripping.

What does nF mean on a Kenmore washing machine?

The nF error code on a Kenmore front-load washer means that the washer isn’t filling with water. The solution is sometimes as simple as opening the water supply faucets behind the washer. Frozen water supply lines and hoses in winter also prevent the washer from filling.

What does E01 mean on a washing machine?

E01 – there’s an issue with the lock, its wiring or connection to the control board. Check the door is closed properly and the wiring is intact. E02 – the machine has failed to fill with water during its allocated time.

What does F2 mean on washer?

: The “F2” fault code indicates it’s taking too long to drain the tub of water in order to reset the pressure switch. The problem is that the washer is not always able to drain water so that the water level switch can reset. This can happen if the wrong type of detergent is used or if you are using too much.

How do you check the pressure switch on a Whirlpool Duet washer?

1. Unplug the Whirlpool Duet washer power cord from the wall outlet. …
2. Go behind the Duet and remove the three screws securing the top panel to the rear panel with a Phillips-head screwdriver. …
3. Adjust the scale on your ohmmeter to the RX1 or X1 scale.

Why is my washing machine not finishing the cycle?

Drainage Problems. If the washing machine doesn’t drain properly then something blocking the pump could have caused the washer to stop mid cycle. … General overheating is again a possible cause for your washer to stop mid-cycle, many washing machines have built-in sensors.

Why does my Maytag washer stop mid cycle?

Maytag Washer stops mid cycle If the door lock is defective, the washer may stop mid cycle. … If the lid switch assembly fails, the washer may stop mid-cycle. To determine if the lid switch assembly is defective, use a multimeter to test each of the lid switches for continuity.

What does DRN mean on Maytag washer?

drn. One of the most common Whirlpool washer error codes, drn signifies a draining issue. There are several possible problems that result in this code being displayed. These are the most likely causes and solutions for a drn error code: Clogs: A blocked drain hose can prevent proper draining.

Why does Maytag washer say LF?

LF in the display When “LF” is displayed, there could be an issue with the water flowing into the machine. Check the water inlet hoses to be sure they are not clogged or kinked. … This means shutting off the water supply, and disconnecting the water inlet hoses from the washer.

What's LF mean on a washer?

Whirlpool Washer LF Error is a water fill error, it stands for Long Fill. It means that the main control has not gotten a signal back from the water pressure sensor which means that water is not filling the tub or not filling the tub fast enough. The control will shut down the cycle and report the LF error.

What does LS mean on a Maytag washer?

The “LS” error code is indicating that the control board cannot detect that the lid switch is opening or closing when the lid is opened and shut. There is a disagreement between the motor and the machine control board on the state of the lid switch.

What does code F51 mean on Maytag washer?

A Maytag washer code F51 means there is a sensor and control board fault or connection issue. … Technically, it’s called a motor rotor position sensor failure (RPS). This can be corrected by either cleaning the sensor, possibly reconnecting it or it may need replacement.

What does E2 mean on Maytag washing machine?

The F0 E2 or Sd error code means your washer has detected an excessive amount of suds in the washer basket. The washer will run an automatic suds reduction routine, to try to eliminate most of the excess sudsing. Allow the washer to continue to run.

What is F5 error code?

An F5 error code indicates that the fan on the outdoor or indoor unit has been running at a very low speed for a set period of time. This occurs when either the controller on the board or the fan malfunctions.

What does HF mean on a Maytag washer?

FH indicates that there is a Water Inlet Problem—no or insufficient water supply. Select PAUSE/CANCEL twice to cancel the cycle. Unplug washer or disconnect power.

What is FH code?

An F20 or FH error code indicates a water supply problem. Here are some common issues: Both hot and cold water must be connected and turned on. Water inlet hoses kinked. Water inlet valve screen clogged.

Why does my Whirlpool washer say FH?

Common solutions for: Whirlpool F/H – FH No Water Entering Machine or Pressure Switch Failure. … Check fill hoses to washer for kinks or clogged screens at water inlet valve. The manufacturer has assigned this error or fault code to indicate that there is a problem with the amount of water entering the machine.

How do I fix the FH code on my Kenmore washer?

1. Look for the “Pause/Cancel” button on the washer control panel. …
2. Press the “Pause/Cancel” button twice to cancel the wash cycle. …
3. Connect the water supply hoses back to the washer and turn on the water spigots.

How do you reset a Kenmore washer?

1. Press the “Stop” button twice, and then press the “Power” button. Video of the Day.
2. Choose a wash cycle (e.g. “Normal”), and then choose your wash options (e.g. “Hot/Cold” or “Cold/Cold”).
3. Press the “Start” button to complete the reset process and restart the washing machine.

What does 03 mean on a Kenmore washer?

@ronhurley the error code “OE” is a “Drain error ” and it is initiated by your washer not having fully drained in 10 minutes. Most common cause is a clogged filter. Check your “coin trap” filter for retained objects, like missing socks etc.:-) To clean it.

What does NP mean on a Kenmore washer?

By Lyle Weischwill. The nd error code on your Kenmore front-load washer means water isn’t draining from the washer. The likely causes are a stopped-up washer drain or a clogged drain pump filter.