What does f5 mean on a Maytag oven
Mia Horton
Updated on April 20, 2026
F5. Keypad Cancel Upper. This oven error code is seen on electric ranges and indicates that the electronic range control board is faulty. This Maytag error code displays when the cook mode and non-cook mode start simultaneously. Repair or replace the electronic range control board to fix this code.
What does F5 mean on an oven?
The “F5” error on General Electric ovens means that the safety circuit failed. This could occur because of a power failure or an error with the lock circuit. Unplug your oven for 30 seconds and plug it back in. If the error remains, replace the lock circuit, using the oven model number to find the proper part.
How do I reset my Maytag oven control panel?
Make sure the Control Lock function is turned OFF. Some ovens may be equipped with Control Lock. Look for “Control Lock” on the oven control console, then reset by, typically, pushing & holding for 3 seconds.
How do I reset my Maytag oven?
- Power unit down by turning off the circuit breaker(s) for one (1) minute.
- Power unit up by turning on the circuit breaker(s).
- Start a bake cycle.
- Monitor the oven for one (1) minute to ensure the error code does not display again.
- Verify oven operation.
Why does my Maytag stove keep beeping?
When the oven beeps, it is to alert the user that the food is complete. Some models will continue to beep as a reminder to take the food out of the oven. Convection ovens also sometimes include a temperature gauge that will cause the oven to beep when it’s at 75% of the original cooking time.
What is F5 error code?
An F5 error code indicates that the fan on the outdoor or indoor unit has been running at a very low speed for a set period of time. This occurs when either the controller on the board or the fan malfunctions.
Why does my oven beep and say F5?
F5 – Control Board Failure – Replace control board (clock). F7 – Function Key Stuck – Replace control board (clock). F8 – Control Board Failure – Replace control board (clock). F9 – Oven Door Lock Failure – Check door lock switches and wiring.
How do I know if my oven control board is bad?
- The display is blank, and none of the buttons are working. …
- It beeps/changes display when you press the buttons, but it still won’t function properly. …
- No beeping/change when you press any button, but the display is still on.
How do I unlock my Maytag oven control panel?
- Press Cancel/Off key to start a latch reset, wait 20-30 seconds and open door.
- Turn the power off at the circuit breaker or fuse box for one minute, then turn the power back on.
- Check the display on your Maytag Gemini range if you hear a beeping sound. …
- Press the “CANCEL” button to get rid of the beeping sound and clear the fault code.
- Disconnect your Maytag Gemini range from its power outlet if it’s still beeping.
How do I get my oven to stop beeping?
Unplugging your oven for 30 seconds and plugging it back can also reset your oven and stop it from beeping continuously.
Why is my oven beeping and F2?
What Does the F2 Error Code Mean? … In this case, the F2 error code indicates that the oven temperature is too high. Now, this does not necessarily mean that the temperature inside the oven really is too high. The oven control board (clock) is responsible for measuring the resistance of the sensor circuit.
What does E1 F5 mean on a Whirlpool oven?
The “E1 F5” error code is a door switch malfunction. This may display if the door is not shut properly, if it is jammed or if the spring-loaded mechanism has broken.
What does code F5 mean on a Maytag washer?
Did you receive a F5 E2 lid lock alert? The F5 E2 alert indicates the washer can’t engage the lid lock because there may be an obstruction in the lid lock area. Please check the lid lock area and remove any objects in that area.
What does F5 mean on an Amana stove?
F5 / F6 / F8 – Control Board Failure – Replace control board (ERC). F7 – Shorted or Stuck Button – Check glass alignment and replace touch pad if necessary. F9 – Door Latch Failure – Replace door latch switch or assembly if necessary.
How do I reset the code on my Maytag F5?
Remove any objects from the lid and clear any obstructions. Touch POWER to exit cycle, then touch POWER again to release lid. If this is unsuccessful, reboot the machine by unplugging the washer and wait two minutes before plugging the machine back in.
How do I fix E5 error on my air conditioner?
E5 Error code indicates that the water collection tank is full. To drain the water collection tank completely, leave the bottom drain cap off long enough to allow any residual water to drain out. Once the water tank is completely drained and no more water flows out, reinstall the cap.
What causes oven control panel not working?
Possible causes are a tripped house circuit breaker for the range, a problem with the outlet cord (not plugged in or broken) or an internal wiring failure. A blown thermal fuse can prevent the control from powering up on some ranges.
How much is an oven control board?
Oven Control Board Replacement Cost Replacing the control board runs between $220 and $300.
Why does my stove work but not my oven?
Let’s say that the stove works fine, but the oven itself never heats up. In most common cases, this specific issue means that the broil element and the baking element remain functional. … If it’s not the fuse, it could be the temperature sensor, broken or frayed wiring, or even a breakdown of the oven control board.
How do you lock a Maytag double oven door?
- Locate the “Cancel” and “Cook & Hold” buttons on the oven’s control panel.
- Hold down “Cancel” then hold “Cook & Hold” with another finger for three seconds. …
- Wait three seconds; the display will change from “OFF” to “LOCK” and the door will seal.
- Repeat these instructions to unlock the door.
What does F9 mean on Maytag oven?
The F9 error code indicates a problem with the oven door lock assembly. The door lock assembly will need to be checked and replaced if defective. If the door lock assembly is okay, then the electronic oven control board will need to be replaced.
Why does my oven say locked?
You may find your oven has arbitrarily locked itself when you weren’t even using it. If you try to use your oven and find it locked, press the “clear” or “reset” button to stop the oven and turn it off. Wait a minute or two and then try to open it again. If it’s still locked, start an oven cleaning cycle.
Where is the temperature sensor in oven?
Your temperature sensor is a probe that extends into your oven on the top left corner of the back interior panel. Reach into your oven along the ceiling, toward the left back corner. You should find it there. If not, check your oven’s manual to find it’s alternate location.
What does F4 mean on an oven?
F4. This code usually means that the oven sensor needs to be replaced. F5. This code usually means that the electronic control needs to be replaced.
Are oven temperature sensors interchangeable?
Most Oven Industries temperature sensors are interchangeable within the specific temperature range for which they are designed – meaning in the event one is damaged, it can be swapped out with no need to recalibrate the thermal system.
What does a control board do in an oven?
When the buttons are used to set the oven’s temperature, an electronic oven control panel controls the oven. Diagnostic codes are displayed when there is a problem with the oven.
How do you test an oven relay?
First, label each wire attached to the relay and remove them from the relay terminals. Using your VOM’s ohmmeter function, set the range to R x 1 and touch one test lead to the terminal marked L and the other test lead to terminal H2. There should be NO continuity. Next, test the terminals marked H1 and H2.
How do I know if my oven fuse is blown?
Visually inspect the fuse to see if it has blown. The fusible link is visible through a glass window in the top. If the fuse is good, this link will be intact. If the fuse has blown due to an overload, this link will be visibly broken.
How do you tell if a fuse is blown?
Remove the fuse from its holder. In some cases you may need a small screwdriver to unscrew the fuse holder cap. Look at the fuse wire. If there is a visible gap in the wire or a dark or metallic smear inside the glass then the fuse is blown and needs to be replaced.
How do I turn off the sound on my Maytag oven?
Hold the Audio button for 3 seconds to turn off all sounds. Lights will still function, but tones will not. This is normal. Hold the Audio button for 3 seconds again to return to tones.
